精密热风烤箱(XRD-HR760C )

Precision hot-air oven (XRD-HR760C )                    

具体制作如下：

Concrete descriptions are as follows:

 内部工作尺寸：L760×W590×H1500。

Dimensions of inner working chamber: L760×W590×H1500

1.      整机总功率：三相，380V，约16KW。

    1．Total power:3P,380V ,about 16KW

2.      外壳采用δ1.5mm冷板制作，内胆采有δ1.5mm不锈钢板制作。

2． The outer plate is made ofδ1.5mmiron,and the inner is made ofδ1.5mmstainless steel.

3.      运风方式：水平送风；内层风道设置可调风网孔板，使炉膛内的风温分布均匀。

3. Adopted horizontal air-delivering .Adjustable air mesh trays fixed in inner layer duct can make the warm air evenly distributed thoughout the chamber.

4.      烤箱底部设置60mm厚保温层，其余部份设置100mm厚保温层，采用进口120K白色岩棉制作，保温效果好，表面温度达到室温。

4. Importing 120K white rockwool madeinsulation layers are installed at the bottom in 60mm thick and other parts in 100mm thick ,which conserves energy and makes the surface temperature reach ambient

5.      烤箱底部设置140mm宽推车槽。安装δ5.0mm厚铁板。

5. 140mm wide cart groove is set at the bottom of oven and it’s fixedδ5.0mmthick iron plate.

6.      烤箱为单开门设置，配不锈钢拉手和可伸缩式卡销。

6. The oven is single –door ,set with stainless steel handle and telescoping bayonet lock.

7.      加温系统采用台湾进口不锈钢发热模组,功率:15KW。

7. Taiwan stainless steel heating module are used in heating system,the power is 15KW.

8.      温度控制采用TAISEE温控器，温度为室温—250℃可调,温控精度在±1℃,炉内温度分布偏差为±3℃。

8. Adopted TAISEE temperature controllerensures a precise and reliable temperature control.The temperature range are ambient temperature to250℃and the temperature inside the oven are controlled with a sensitivity of ±1℃,spatial deviation in temperature are±3℃.

9.      运风马达循环风速大小由1台1HP台产变频器控制。

9.  Circulating air speed is controlled by 1 set of Taiwan 1Hp frequency converter

10.   烤箱配置1台运风马达采用台湾进口1HP高温长轴马达(保修五年)，运风轮采用10.5寸加强型多翼式风轮。

10. The oven is installed with 1 set of Taiwan 1HP long axis air-delivering motor ,and the air-delivering wheels are adopted 10.5 inch reinforced multi wings wind wheels.

11.   电箱设置电源指示、故障指示、时间制（0-999h）、散热电脑风扇并设超温超时控有声报警及系统,计数器预定的时间到达时，烤箱开始报警，员工关掉计时器开关和报警开关，警灯报警停止，换新的材料烘烤时只需把计时器开关复位即可,烤箱重新开始正常工作。

11. The electric box is set with power LED,failure indicator,timer(0-999h),computer cooling fan , overtemperature and overtime alarm, and power automatic cut-off control system.The oven will alarm when the time reaches the setting value,turn off the timer switch and alarm swtich ,alarm stops.When bake new materials,only reset the timer and the oven will work again.

12.   烤箱内的产品烘烤时间完成时，如果暂时不需要再烘烤产品，烤箱报警时，关掉计时器开关的同时也关掉报警开关，烤箱开始降温。

12. When the products are baked well,and if do not bake other products,the oven alarms,turn off the timer switch and also turn off the alarm switch ,the oven will cool down.

13.   烤箱顶部设置废气排放口Ø95MM，并设置废油回收及排出，防止烤箱内部高温火灾。

13. Ø95MM exhaust emission outlet is set at the top of oven,also waste oil’s recycling and exhausting are set to prevent from the fire because of the high temperature in chamber.

14.   表面经专业防锈,腐处理后，喷电脑色烤漆。

14. The surface is sprayed with long lasting stove enamel after professional rust proofing.