| 热熔压敏胶 主要成分:天然橡胶、合成树脂 质量标准: 外观:米白透明块状弹性固体 固含量:100% 软化点:85±5℃ 熔融粘度:(170℃)/mpa.s.2800cps 纯洁度:加热至180℃、200目筛网全通过 初粘力:12#钢球(滚球法) 持粘力:38h 180℃剥离强度∕N∕2.5cm)≥30 使用说明:1、推荐上胶方式:喷涂或滚涂 2、操作温度155~180℃ 3、胶箱或胶箱如有积碳,可先用普通石蜡或矿物油清洗再用热熔胶在135℃左右冲洗 4、本品上胶时的粘度可通过温度进行调节 5、本品不得与其他牌号热熔胶混合使用 6、往热熔胶槽加料后,应立即关闭胶槽盖子,以防外来杂质污染。 安全事项:1、操作中往热熔胶槽加料时应佩戴防护眼镜与防热手套 2、使用场所应通风良好并严禁一切明火 3、在任何时候使用温度都不能超过200℃ 特点及用途:本品呈无色透明状,无臭味无毒性,具有粘接力强,耐老化性能好,耐高温性能好基材适用性广等特点,适用于卫生巾及卫生护垫用背胶、结构胶、以及婴儿纸尿裤的橡筋固定结构胶、化妆盒、吸塑产品、FET、PP、PVC、PE等薄膜,还可以用于常见粘扣带泡绵、塑料、纸的粘接复合无纺布等难粘接复合。 存储及运输:储存于阴凉干燥处避免阳光直射,储存温度应底于35℃并远离火源,保质期1年安排危险品运输 包装:本品20Kg纸箱包装 Hot-melt pressure-sensitive adhesive Main components: natural rubber, synthetic resin Quality Standards: Appearance: off-white solid transparent block flexibility Solid content: 100% Softening point: 85 ± 5 ℃ Melt viscosity: (170 ℃) / mpa.s.2800cps Purity: heated to 180 ℃, 200 mesh full by Tack: 12 # ball (ball method) Holding power: 38h 180 ℃ peel strength / N/2.5cm) ≥ 30 Instructions for use: 1, recommended glue method: spray or roller 2, the operating temperature of 155 ~ 180 ℃ 3, plastic boxes or plastic boxes, if carbon can be normal paraffin or mineral oil with a clean hot melt at around 135 ℃ and then washed 4, when the materials of plastic viscosity can be adjusted by temperature 5, the goods shall not be mixed with other grades of hot melt adhesive 6, after the feeding to the hot melt tank, plastic tank lid should be closed immediately to prevent foreign matter contamination. Safety matters: 1, hot melt tank to the feeding operation should wear safety glasses and heat-resistant gloves 2, using the site should be well ventilated and are prohibited from all fire 3, the temperature at any time should not exceed 200 ℃ Features and uses: This product was colorless and transparent, no odor non-toxic, with strong adhesion, anti-aging properties, high temperature performance characteristics of the substrate and wide applicability for use in sanitary napkins and panty liners back adhesive, structural adhesive, and the fixed structure of rubber baby diapers plastic, cosmetic, plastic products, FET, PP, PVC, PE film, etc., can also be used for common Velcro foam, plastic, paper sticky difficult to access non-woven composite adhesive compound. Storage and transportation: Stored in a cool dry place away from direct sunlight, storage temperature should be 35 ℃ and at the end away from the fire, one-year shelf-life arrangement of dangerous goods transport Packing: 20Kg cardboard packaging of this product | |